Monday, November 30, 2015

Angel Hug Gift Card Holder

Angel Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 6.25” (Not including wings)

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222


Friday, November 27, 2015

Reindeer Gift Tag



Reindeer Gift Tag-JMRush
This design can be used as a gift tag or ornament and is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222


Wednesday, November 25, 2015

Poinsettia Gift Card Box



Poinsettia Gift Card Box-JMRush
Box size: W 3.5 x D 2.5 x H .75”

This gift box has a hinged top lid and is sized to fit most gift cards. The poinsettia flower can also be used separately. This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces.
2. Fold box score lines. 
3.Apply glue to the outside of the top tabs.
4. Secure to the top panel. Apply glue to the next set of tabs.
5. Secure to the rectangular shape just above the tabs. Apply glue to the last set of tabs.
6. Secure to the last rectangular panel. Your box will be complete now. Fold flower score lines. Fold one in and one out on each size. Fold leaves in half.
7. Line up the points of the flower on the largest set of two. Make sure you have one flower fold down and one up. Glue the center to secure it together.
8. Apply glue to the flower edges and secure.
9. Repeat for the two smaller sets of flower petals.
10. Curve the petals and Leaves as you like after it dries.
11. Glue the leaves on the top of the box.
12. Glue the flower sets on the box staggering the layers. I used foam adhesive squares in between each layer to give the flower more dimension.
13. I used four small adhesive gems in the center of the flower it give a bit of sparkle:)
14. Your Poinsettia Gift Card box is complete.


Tuesday, November 24, 2015

Merry Christmas Poinsettia Card

Merry Christmas Poinsettia Card-JMRush
Card size: 5.5” x 4.25”

This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222



1.Cut design pieces.
2. Fold all score lines. For each set of the flowers- fold one in and one out.
3.- 4. Apply glue to bottom of the rectangular border piece and center on the top of your card. Center the lettering on the lettering base and glue into place.
5. Line up the points of the Largest flower set. Make sure you have one flower fold down and one up. Glue the center to secure it together.
6. Apply glue to the flower edges and curve the petals as you like after it dries.
7. Repeat for the other two flower sets.
8. Attach the centers of the flowers together. I used small pieces of foam adhesive squares to give it more dimension. Curve the flower petals and leaves as you like.
9.Glue the leaves onto your card and then your flower. I again used foam adhesive square pieces to secure the flower onto the card base. Glue your lettering into place and finish with adhesive jewels in the center of your flower:) Your card is complete!



Elf Hug Gift Card Holder



Elf Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 7”

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces.
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4. Flip the Face so that the bottom side is face up. Center and glue the teeth onto the face piece. Glue the buckle onto the belt.
5. Flipping the face piece face up glue it onto the face base. Glue on the Hair. Glue the Belt onto the gift card section.
6. Glue the collar piece into place. Glue the hat to the backside of the card base.
7. Glue on the hat trim and feather. Using a piece of foam adhesive square, attach the nose. Glue on the hands and trim. Finish by adding a bow in-between the slots on the gift card section:)

Yeti Hug Gift Card Holder



 Yeti Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 6.25” 

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222



1.Cut design pieces.
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4. Flip the Head/Beard Piece so that the bottom side is face up. Center and glue the Face onto the Head/Beard piece. 
5. Glue on the black solid head piece. Flip your combined head piece over so it is facing you.
6. Glue the teeth and eyes into place. Attach he nose by using a piece of square foam adhesive.
7. Glue on the hands and trim. Finish by adding a bow in-between the slots on the gift card section. I used adhesive dots to give the eyes a little extra pop:)

Monday, November 23, 2015

Santa Gift Tag

Santa Gift Tag-JMRush

This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222




Reindeer Antler Handles Box



Reindeer Antler Handles Box-JMRush

W 5" X  H 4” X D 1.25” (Not including handles)

This Reindeer Box can be filled with your favorite goodies. This design is compatible with 8x12 or 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222




1.Cut design pieces.
2. Pre-Fold all score lines.
3.Apply glue to the tabs on the second section.
4. Secure to the third section from the top. Apply glue to the tabs of the third section. Secure to the first section, creating a box.
5. Apply glue to the wings of section four.
6. Secure to the inside of the wings of section five.
7. Glue on the Reindeer head. Insert the Lid tab into the slot to close the box.
8. Insert the antlers into the slots in the top of the box base on the front and backside.
9. I used a foam adhesive square to attach the nose. Glue on the eyes. I used adhesive dots on top of the eyes to give them more dimension:)
10. Finish with a ribbon if you like:)

Christmas Lantern (Flameless)




Christmas Lantern (Flameless)-JMRush
Lantern size: W 3 x D 3 x H 7”

This Flameless Christmas Lantern features cut outs and when vellum paper is used, a layered transparent frosted glass effect is created. This design is compatible with both 8X12 and 12X12 mats.
You may also want to check out: Santa Kissing Momma Lantern 

You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222

http://jmrushdesigns.blogspot.com/2015/12/santa-kissing-momma-lantern-flameless.htmland the Nativity Scene Lantern (Flameless) http://jmrushdesigns.blogspot.com/2015/12/nativity-scene-lantern-flameless.html


1.Cut design pieces. ( This picture shows more snowflakes then what is contained in your file. They were unnecessary and deleted:)
2. Fold all score lines. Glue the vellum paper to the back sides of the window panels.
3.Apply glue to the long side tab of the lantern window base and secure to the other lantern window base piece.
4. Apply glue to the top tabs of the Lantern square base and secure to the inside of the sides.
5. Repeat for the bottom tabs creating a shallow box. Apply glue to the front side of the window panels.
6. Flip the Lantern window base over ( You will be working on this inside of the lantern) and secure the window panels centering each one to each window cut out on the window base. Apply glue to circular part of one of the hangers.
7. Glue the circular hangers together. ( Make sure the stems of this piece remain separate) Glue one of the stems to the inside of the top of the second window panel. 
8. Flip the Lantern over again ( the outside is facing you now). Apply glue to the top tabs and to the side long tab.
9. Secure the Long side tab to the other side creating a box.
10. Begin to secure the top tabs to the inside of the next angled triangle. 
11. The other Circular hanger stem will be glued to the inside of the opposite side of the lantern. 
12. This is what it should look like:)
13. Finish securing all of the top tabs. 
14.Place the Lantern in it’s base. Glue the snowflakes on to the outside of the window panels.
15. Attach the small snowflake to the large one using a piece of foam adhesive square and then attach the snowflake to the lantern. I used a adhesive gem for the center of the snowflake. ( Please ignore the extra unnecessary snowflakes shown in the photo:)
16. Finish with a ribbon and place a flameless candle inside.

Polar Bear Hug Gift Card Holder



Polar Bear Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 6.5” 

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces. ( There is an optional rectangular “Scarf” piece incase you choose to use cardstock for the scarf instead of ribbon)
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4. Using pieces of foam adhesive squares, attach the trim pieces to the mittens, the nose to the circular face piece, and the glue the puff ball to the hat base.
5.Glue the Hat Base piece to the Card Base. Using foam adhesive squares attach the hat brim to the hat base and attach the circular face piece to the card base. Glue the eyes on.
6. Glue the mittens to the backside of the paws.
7. I used ribbon as the scarf. I included rectangular cut piece in this design file incase you want to use cardstock for the scarf:)
8. Insert the gift card.
9. The Mittens tuck into the slots on the card base to close the card:)

Snowman Earmuff Hug Gift Card Holder


Snowman Earmuff Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 6” 

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces.
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4.Glue the Scarf piece to the Card Base.
5.Attach the earmuffs onto the head with glue. Attach the oval earmuffs to each side and the carrot nose to the caner of the head with foam adhesive squares.
6. Glue the eyes and the mouth circles on. Glue the button between the two slots on the card base.
7. Glue the two remaining buttons to the inside.
8. Insert the gift card.
9. The Hands tuck into the slots on the card base to close the card:)

Penguin Hug Gift Card Holder


Penguin Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 6.5” 

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.
You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1.Cut design pieces.
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4.Glue the Oval Body piece to the Card Base.
5.Attach the nose onto the head with a adhesive foam square. Glue the Hat Base on and the puff ball onto the hat base. Using foam adhesive squares, attach the hat brim onto the hat base.
6. Glue on the mitten pieces to the back of each wing. Using pieces of foam adhesive squares attach the mitten trim pieces onto each mitten.
7. Insert gift card.
8. The mittens tuck into the slots on the card base to close the card:)



Reindeer Hug Gift Card Holder



Reindeer Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 7” 

This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.  

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1.Cut design pieces.
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4.Glue the Oval head piece to the head piece with antlers.
5.Attach the nose on to the head and the completed head onto the card base with adhesive foam squares.
6. Glue on the yoke piece on the card base around the reindeer head. glue on the jingle bell designs.
7. Glue on the hoof pieces to the back of each leg.
8. Finish by adding a bow in the middle of the two slots in the card base. The hooves tuck into these slots to close the card:)
9. Insert gift card and TA DA:)! Your gift card is complete:)



Santa Hug Gift Card Holder



Santa Hug Gift Card Holder-JMRush
Approximate Card size: 4” x 5.75”


This card features character arms that open to release a hidden gift card section.This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1.Cut design pieces. I used double sided red cardstock for the card base:)
2. Fold the card along score lines.
3. Apply glue the bottom of the side tabs on the card base. Secure by folding upward toward the card base.
4.Glue the Oval head piece and the hat sliver on top. Glue on the Santa’s belt and buckle.
5.Glue on Santa’s face.
6. Using foam adhesive squares, place and attach Santa’s mustache. Using glue, attach the eyes and nose.
7. Glue Santa’s hand to the arm wings and then glue on the trim pieces to each hand.
8. Place gift card.
9. Tuck Santa’s hands into the cut slots in the card base.

10. Glue a ribbon in the center of the slots to finish:)

Monday, November 16, 2015

Ornament Swing Card





Ornament Swing Card-JMRush
Card size: W 4.25" X 5.5”

This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222



1.Cut design pieces.
2. Fold the card score line. Stack the small rectangular piece on top of the the ornament holder and glue into place. I used a foam adhesive square. Place the second largest ornament piece onto of the largest one. I lined it up toward the upper right. Glue into place.
3.Apply glue to the bottom of the smallest circle and place on top of the second smallest- again lining it up  toward the upper right. Glue this second onto the other ornament pieces.
4. Place a piece of ribbon through the open circle of the ornament holder glueing it on the back( I used hot glue).
5. Apply a dab of hot glue to the opposite end of the ribbon and attach to the top center of the card base. Glue a bow on top to finish it.
6. Your card is complete and your ornament should be able to swing:)

Santa’s Bag Pocket Gift Card Holder

Santa’s Bag Pocket Gift Card Holder-JMRush
Card size: W 4.25" X 5.5”

This pocket card has a removable insert that will hold a standard size gift card. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces.
2. Fold all score lines.
3.Apply glue to the tabs on the card base and secure to the inside of the opposite side.
4. Apply glue to the side and bottom tab of the insert piece. Secure to the inside of the opposite side.
5. Apply glue to the backside of the present panel. 
6. Secure to the front of the insert piece. The small square piece is glued to the middle of the bow.
7.Glue the letters to the lettering bases and attach the belt buckle to the belt piece. (I used foam adhesive squares for the buckle.)
8.Glue the belt onto the card base. Attach the letters onto the card base. (I again used foam adhesive squares for the lettering.)
9.This is what your designs should look like:)
10. The gift card fits in between the layers of the insert.
11. Finish by adding a ribbon.

Holly Gift Card Box


Holly Gift Card Box-JMRush
Box size: W 3.5 x D 2.5 x H .75”

This gift box has a hinged top lid and is sized to fit most gift cards. This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222


1.Cut design pieces.
2. Fold all score lines.
3.Apply glue to the outside of the top tabs.
4. Secure to the top panel. Apply glue to the next set of tabs.
5. Secure to the rectangular shape just above the tabs. Apply glue to the last set of tabs.
6. Secure to the last rectangular panel. Your box will be complete now. Apply glue to one bottom side of your holly leaf. Attach the matching leaf.
7.Repeat for the other leaves. Glue the holly berries to their matching bases.
8. Glue the leaves onto your box. I used adhesive foam squares to attach the berries.
9. Your gift box is complete:)

Happy Birthday Deco Flower Card


Happy Birthday Deco Flower Card-JMRush
Card size: 5.5” x 4.25”

This design is compatible with both 8X12 and 12X12 mats.

1.Cut design pieces.
2. Fold the Card along score lines. Center the lettering on the lettering base and glue into place. Center the rectangular border on the front and glue into place.
3. Match up the flowers with their bases and flue into place. I used foam adhesive square on the two largest flowers to add dimension to the design:)
4.Using foam adhesive squares, attach the two largest flowers into place.
5. Finish by adding adhesive jewels to the center of the flowers.
6. Ta Da:) Your card is complete!

Saturday, November 14, 2015

Happy Holidays Layered Card


Happy Holidays Layered Card-JMRush
Card size: 5.5” x 4.25”

This card features a layered snowflake frosted effect when vellum paper is used. This design is compatible with both 8X12 and 12X12 mats.

1.Cut design pieces.
2. Fold the Card along score lines. Center the lettering on the lettering base and glue into place.
3. Glue the bottom layer (the rectangular piece with he most cut outs) onto the card face. Glue the open rectangular piece on top of the vellum piece.
4.Use foam adhesive squares on the backside of the vellum border piece to attach it to the card base. The adhesive foam squares provide more space in between the layers which assists the frosted effect.
5. Attach the lettering. Finish by adding adhesive jewels.
6. Ta Da:) Your card is complete!

Reindeer Gift Card Box


Reindeer Gift Card Box-JMRush
Box size: W 3.5 x D 2.5 x H .75”

This gift box has a hinged top lid and is sized to fit most gift cards. This design is compatible with both 8X12 and 12X12 mats.



1.Cut design pieces.
2. Fold all score lines.
3.Apply glue to the outside of the top tabs.
4. Secure to the top panel. Apply glue to the next set of tabs.
5. Secure to the rectangular shape just above the tabs. Apply glue to the last set of tabs.
6. Secure to the last rectangular panel. Your box will be complete now. Apply glue to the front of your antler rectangle.
7.Attach it to the backside of your box. Glue on the eyes and nose. I used foam adhesive to attach the nose.
8. I used adhesive dots on top of the eyes.
9. Your reindeer is complete:)

Wednesday, November 11, 2015

Acorn Small Favor Box



Acorn Small Favor Box-JMRush
Finished dimensions of the box (approximate): L 3” X W 2.25 X H 1.5

The Acorn Small Favor Box is perfect to enclose a small gift or goodies. The Acorns that adorn the top can be used separately. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222



Tuesday, November 10, 2015

Snowman Gift Card Box


Snowman Gift Card Box-JMRush
Box size: W 3.5 x D 2.5 x H .75”

This gift card box has a hinged top lid and is sized to fit most gift cards. This design is compatible with both 8X12 and 12X12 mats. 

1.Cut design pieces.
2. Fold all score lines.
3.Apply glue to the bottom of the top tabs. Secure to the top panel.
4. Apply glue to the next set of tabs. Secure to the rectangular shape just above the tabs.
5. Apply glue to the last set of tabs. Secure to the last rectangular panel.
6.Your box will be complete now.
7. Glue on the hat and eyes.
8. Glue on the decorative strip to the hat.
9. I used foam adhesive squares to attach the hat brigand the carrot nose.
10. Glue on the mouth dots.
11. Glue on the arms positioned how you like.
12. I finished my snowman with ribbon trim ( The ribbon does not carry around to the backside so the box will still be functional:) and with adhesive gems on his hat.

Snowman Treat Box



Snowman Treat Box-JMRush
Box size: W 2.25 x D 2 x H 3”

This treat box has a hinged top lid and can be filled with your favorite goodies. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:


You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222



1.Cut design pieces.
2. Fold all score lines.
3.Apply glue to the bottom of the bottom tab. Secure to the bottom square panel.
4. Apply glue to the bottom of the next two tabs on the other side of the bottom square panel.
5. Secure to the square panel and apply glue to the side tab, forming your box.
6. The Lid tab will fit into the slot to close your box.
7. Place the tab of the hat piece into it’s slot, forming a circle. 
8. Apply glue to the inside to hold it in place.
9. Slide the circular hat brim over the hat piece.
10. Glue the tabs on the bottom of the hat piece to the bottom of the hat brim piece.
11.Secure in place and let dry.
12. Apply glue to the top tabs.
13. Center the full circle on top of the joined hat pieces and glue into place.
14.Apply glue to the top of your box.
15. Attach the hat to the top of your box. Glue the eyes nose and mouth into place. 
16.Glue buttons into place.
17-18I used a length of 12.5” ribbon as the snowman’s scarf glueing it around the snowman box.
19. Apply glue to the top of the bottom of the snowman arms.
20. Attach to the upper back corner on each side.
21. I finished the snowman by adding a ribbon around his hat.Your snowman is complete:)



Monday, November 9, 2015

Ornament Gift Card Box



Ornament Gift Card Box-JMRush
Box size: W 3.5 x D 2.5 x H .75”

This gift box has a hinged top lid and is sized to fit most gift cards. This design is compatible with both 8X12 and 12X12 mats.


1.Cut design pieces.
2. Fold all score lines. 
3.Apply glue to the outside of the top tabs. 
4. Secure to the top panel. Apply glue to the next set of tabs.
5. Secure to the rectangular shape just above the tabs. Apply glue to the last set of tabs.
6. Secure to the last rectangular panel. Your box will be complete now. Apply glue to the backside of one of your folded circular ornaments.
7. Align another one of the circular shapes to it and secure. Apply glue to the backside of that piece.
8. Align the third circular shape and secure. Apply glue to the backside of that piece and repeat for the final circular shape.
9. Glue a 2" piece of ribbon to the top center of your box and the glue the backside of your joined circular ornament pieces on top.
10. Finish by glueing a ribbon to the top of the ornament:)