Valentines BirdHouse Treat Box

 Valentines BirdHouse Treat Box-JMR

Approximate size: W 3 x D 1.75 x H 3.5”

Approximate box size: W 3 x D 1.75 x H 2”

This cute bird house treat box opens from the handles on the top. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1.Cut design pieces. ( I used double sided card stock)

2. Flip the birdhouse box over and fold the bird house base at the score lines.

3. Connect the two wing tabs on the bottom.

4. Apply glue to the bottom of the connected wing tabs and fold in the small bottom tab. Hold until secure.

5. Apply glue to the bottom of the birdhouse box and secure the last large square bottom panel; aligning at the edges.

6. Apply glue to the side tab and connect the side panel.

7. Curve the flowers and leaves as you like.

8. Combine the two large petal groups by glueing the middle circle; Larger on bottom and alternating petals. Repeat for the two smaller petals. Glue the smallest circle to the larger one; centering it.

9. Glue the two petal groups together; alternating petals. Glue the leaves to the bottom of the combined flower. Attach a piece of foam adhesive to the bottom.

Attach the combined circles with a piece of foam adhesive square as shown.

10. Attach the combined flower as shown. Push in the two top handle panels.

11. Apply small pieces of foam adhesive square to the backsides of the two triangular roof top pieces and attach to front and backside of the birdhouse box.

12. Finish with a ribbon and I used an adhesive jewel for the center of the flower:)

 

Robot Treat Egg Holder

Robot Treat Egg Holder -JMR

Approximate size: H 4.75” X W 5.5” X D 2.5”

This easy to construct robot treat egg holder is compatible with both 8X12 and 12X12 mats and is sized to hold a Kinder Joy chocolate egg.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1. Cut the design pieces. I used double sided card stock.
2. Glue the gray rectangle with eye cutouts to the coordinating black robot head base solid shape; centering it. Using foam adhesive squares; attach the smaller silver squares to the larger gray squares.
3. Glue two of the silver C shaped robot hands to the coordinating shape on the box base. Use foam adhesive squares to attach the silver robot head shape with eye and mouth cutouts to the combined robot head.
4. Glue the combined robot head and two of the ears to the box base. Use pieces of foam adhesive squares to attach the heart to the box base and one of the small gray circles to the antenna.
5. Flip the box base over. Fold the score lines inward. Apply glue to the two side tabs. Fold the bottom section up to meet the tabs creating a box. Hold until dry.
6. Apply glue to the small horizontal tab. Tuck under the alien figure enclosing the box.

7. This is what it should look like:)
8. Match up the full figure to the backside of the box base making sure the top matches. Apply glue and attach to the back of the box base.
9. Glue the full silver rectangle, small circle antenna, remaining two ears, and remaining two C shaped robot hands to the back of the box base.

10. Flip robot over and attach the combined square feet to the front of the box base using foam adhesive squares. I added adhesive enamel jewels to enhance the eyes and a kinder egg.

Vampire Treat Egg Holder

Vampire Treat Egg Holder -JMR

Approximate size: H 5” X W 4.5” X D 2.5”

This easy to construct Frankenstein treat egg holder is compatible with both 8X12 and 12X12 mats and is sized to hold a Kinder Joy chocolate egg. 

 You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1. Cut the design pieces. I used double sided card stock.
2. Glue the vampire face to the coordinating shape on the box base. Glue two of the four curve hands to the front of the full vampire shape as shown.
3. Glue the eyes and collar into place on the box base.
4. Use pieces of foam adhesive squares to attach the red bow tie and the tiny little oval nose. I used adhesive jewels to accentuate the eyes.
5. Flip the box base over. Fold the score lines inward. Flip the full silhouette over and glue the ear/neck section and two remaining hands in place.
6. Apply glue to the two side tabs. Fold the bottom section up to meet the tabs creating a box. Hold until dry. Use pieces of foam adhesive squares to attach the cape collar on the vampire silhouette piece.

7. Apply glue to the small horizontal tab. Tuck under the vampire figure enclosing the box.

8. Apply glue to the backside of the vampire box base and attach the solid full body shape aligning at the edges.

9. This is what it should look like:)

10. Flip the box over to the front and attach the oval red shoes with foam adhesive squares.

Werewolf Treat Egg Holder

Werewolf Treat Egg Holder -JMR

Approximate size: H 5” X W 6.25” X D 2.5”

This easy to construct Werewolf treat egg holder is compatible with both 8X12 and 12X12 mats and is sized to hold a Kinder Joy chocolate egg. 

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1. Cut the design pieces. I used double sided card stock. (You will have two of the orange t-shirt shapes.
2. Glue the werewolf eyes with cutouts to the coordinating base solid eye shape; centering it. Flip the box base over and fold score lines.
3. Glue the combined eyes to the back of the Werewolf face shape so the the combined eyes show through.
4. Using pieces of foam adhesive squares, attach the top of the werewolf face to the full solid werewolf face shape.  Use glue to attach the mouth section.
5. Using pieces of foam adhesive squares, attach the nose to the cording shape on the werewolf face. 
6. Glue the tiny white teeth (2) to the coordinating shape on the combined werewolf head.

7.  Apply glue to the two side tabs. Fold the bottom section up to meet the tabs creating a box. Hold until dry.

 8. Apply glue to the small horizontal tab. Tuck under the werewolf figure enclosing the box.

9. Flip the box base over. Fold the score lines inward.

10. Apply glue to the backside of the werewolf figure and attach the solid full body shape aligning at the edges. 

11. Flip the box base over. Glue one of the orange t-shirt shapes to the front; aligning at the side edges.

12. Using foam adhesive squares, attach the combined werewolf face to the coordinating shape on the front of the box base. 

13. Using pieces of foam adhesive squares, attach the feet and ears to the coordinating shapes on the box base.

14. I used adhesive jewels to accentuate the eyes.

15. Flip box base over. Apply glue to the back of the last orange t-shirt and attach to the back of the box base.

16. Using foam adhesive squares, attach the tail to the back of the box base.

17. This is what it should look like:)

 

Vampire Gift Tag Ornament

Vampire Gift Tag Ornament-JMRush

Approximate Size: W 3.25” x H 4.5”

This simple to construct design would be perfect to label your goodies for Halloween parties. This design is compatible with both 8X12 and 12X12 mats. 

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut the design pieces. ( I used double sided card stock)

2. Glue the hair piece to the coordinating shape on the round head piece with eye mouth cut outs. Glue the hands to the coordinating shapes on the tag base. Glue the white collar sleeve piece in place on the combined tag base. Glue the tiny oval to the nose base; aligning at the top.

3. Glue the combined nose to the head piece. Glue the bow tie and buttons to the tag base.

4. Place the combined head over the tag base aligning at the top and sides of the coordinating shape. Using a pencil, mark where the eyes should be places.

5. Remove combined head and place enamel jewels on the pencil marks. (I added a ribbon over the bow tie and adhesive jewels over the buttons.)

6. Attach the combined head with adhesive foam squares.

7. This is what it should look like:)

8. Flip the design over and glue the white body shape into place so that you have a place to write (optional).

 

Black Cat Open Mouth Treat Box

Black Cat Open Mouth Treat Box-JMRush

Approximate Size: W 5” x D 1.25”x H 5.5”

Approximate Box size: W 2.5” x D 1 x H 4” 

This box opens by lifting the character’s head to to expose the opening to the treat box. This simple to construct design would be perfect to hold your goodies for Halloween or birthday parties. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut the design pieces. ( I used double sided card stock)

2. Fold the box and Mouth base at the score lines.

3. Glue the pink mouth piece (with holes) to the coordinating shape on the mouth base;aligning at the inner oval cut out shape.

4. Use pieces of foam adhesive squares to attach the teeth shapes to the coordinating shapes on the combined mouth base.

5.  Glue the two tiny oval white pieces to the coordinating shapes on the eyes. This is what it should look like:)

6. Flip the mouth base top over, like so. Glue the Cat head to the coordinating shape; aligning at the top of the ears.

7. I used an orange marker on the edges of the cat eyes. Glue the cat eyes into place.

8. Place the Cat nose on the cat face to find placement and then remove.

9. Cut thread ( approximately three strands of 4inches).

10. Attach the threads with glue to the area you picked to place the Cat nose. Allow to dry.

11. Using a foam adhesive square, place the Cat nose on top of the threads.

12. I used adhesive jewels to accent the eyes.

13. Apply glue to the small vertical side tab at the left side of the bottom of the box base.

14. Secure the small vertical side tab to the 1 inch (width) rectangles just above. 

15. Apply glue to the very left vertical tab, the horizontal tab, and the side tab on the bottom right and attach the side and bottom of the base…wrapping it crating a box.

16. This is what it should look like:)

17. Tuck the tab into the slot on the top.

18. Flip the box base over and apply glue to the area just outside the oval cut out.

 19. Attach the combined Cat head; centering it around the cut out oval shape and allow to dry.

20. I finished by adding a ribbon and filling with fun sized candies.

Santa Chocolate Belly Holder

Santa Chocolate Belly Holder-JMRush 

Approximate size: W 4.5 x D 2.25 x H 4.25”

This easy to construct chocolate holder is compatible with both 8X12 and 12X12 mats. A complete step by step picture tutorial can be found on my blog.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1. Cut the design pieces. I used double sided card stock. (There is a solid santa piece in this file that is not shown in this image tutorial. It is used as a backing. Sorry. I forgot to cut this piece)
2. Flip the box base over. 
3. Apply glue to the side tabs and secure the bottom panel; aligning at the edges.
4. Apply glue to the last tab and tuck under the snowman shape;align at the edge.
5. Image of the backside. Apply glue to the backside of the santa shape (not shown in image) and secure the solid santa to the santa base; centering it.
6. Flip the combined santa to the front. Glue the belt buckle to the center of the belt. Glue the belt so it forms a circular shape the size of the chocolate. Place the belt around the chocolate.
7. Use a glue to attach the hat, face, hat brim pieces to the santa head. Use pieces of foam adhesive squares to attach the heels of the shoes to their shoe bases.
8. Glue the hands and cuffs to the santa box base. Glue the tiny eyes to the combined santa head. Glue the tiny nose to the upper center of the mustache piece. Use a piece of foam adhesive squares to attach the combined mustache to the combined head.
9. Glue the combined head to the combined santa base. Use foam adhesive squares to attach the feet to the box base:)

Snowman Chocolate Belly Holder

Snowman Chocolate Belly Holder-JMRush 

Approximate size: W 3.5 x D 2.25 x H 4.25”

This easy to construct chocolate holder is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here:https://www.jamieandjenn.com  Coming Soon:)

1. Cut the design pieces. I used double sided card stock.
2. Flip the box base over. 
3. Apply glue to the side tabs and secure the bottom panel; aligning at the edges.
4. Apply glue to the last tab and tuck under the snowman shape;align at the edge.
5. Image of the backside. 
6. Apply glue to the backside of the snowman shape (as shown) and secure the solid snowman to the snowman base; centering it.
7. Flip the combined snowman to the front.
8. Use a glue to attach the hat, nose, arms, and scarf piece to their coordinating shapes on the combined snowman base.
9. This is what it should look like:)
10. Glue the belt buckle to the center of the belt. Glue the heels of the shoes to the shoe bases.
11. Glue the belt so it form a circular shape the size of the chocolate.
12. Place the belt around the chocolate. I used small adhesive jewels to accent the eyes.

White Long Hair Cat Handle Basket

White Long Hair Cat Handle Basket- JMRush 

Approximate Box size: H 2.25” X W 3” X D 2.25”

Approximate Design size: W 4.5” X H 5.5” including handle

This cute basket design is a perfect container for treats for your favorite feline, a small gift for your veterinarian, or a party favor. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here: https://www.jamieandjenn.com  

1. Cut design pieces. ( I used double sided card stock and glitter card stock of the eyes) (There are two pink noses in this file that is not shown in the tutorial and I adjusted the tail to be larger)
2. Glue the face piece with openings and a chin to the coordinating black solid cat face. I used a marker to color the outside edges of both large blue eyes. Glue them to the openings in the combined cat face. Glue the smaller solid paws and feet to the larger solid feet and paws.
3. Glue the fury bottom piece to the coordinating shape on the lower section of the basket base. Glue the other fury chest/head piece to the coordinating shape on the upper section of the basket base.
4. Glue the combined cat face to the cat face/chest piece. Glue the inner ears to the coordinating shape on the combined cat face. Using foam adhesive squares, attach the smaller tail to the coordinating shape on the larger tail. Glue the small oval white pieces to the cording shapes on the cat’s eyes.
5. Attach the smallest cat head (with cut outs) to the combined cat face using foam adhesive squares. Glue the nose into place.
6. Glue the combined cat to the coordinating shape on the basket. Use foam adhesive squares to attach the front paws to the top section of the basket and the back feet and tail to the bottom section.
7. I used enamel dots to accentuate the eyes.
8. Flip the combined basket over. Fold the basket base at the score lines.
9. Apply glue to the top two tabs on the basket base and secure to the Cat shape above.
10. Apply glue to the bottom two tabs on the basket base and secure to the rounded shape above creating a box.
11. Image of box completed.
12. Insert the handle on either side of the basket.
13. I added a ribbon.
14. Use three small lengths of thread and apply hot glue to one of the groups of ends. Attach the nose. Repeat for the other side:)
15. Image of the whiskers glued.
16. Hot glue the second pink nose on top of the whiskers:)

Black Cat Handle Basket

Black Cat Handle Basket- JMRush 

Approximate Box size: H 2.50” X W 3” X D 2.50”

Approximate Design size: W 4.5” X H 5.5” including handle

This cute basket design is a perfect container for treats for your favorite feline, a small gift for your veterinarian, or a Halloween party favor. This design is compatible with both 8X12 and 12X12 mats. 

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

You can purchase the SVG and Cricut compatible file here: https://www.jamieandjenn.com  

1. Cut design pieces. ( I used double sided card stock and glitter card stock of the eyes) 
2. Glue the fury bottom piece to the coordinating shape on the lower section of the basket base. Glue the other fury chest/head piece to the coordinating shape on the upper section of the basket base. I used a marker to color the outside edges of both large yellow eyes.
3. Glue the yellow eyes to the coordinating shape on the combined basket. Glue the smaller solid paws and feet to the larger solid feet and paws.
4. Attach the cat head ( black with cut outs) to the combined basket using foam adhesive squares.
5. Use a small piece of foam adhesive square to attach the nose. ( Hint- I use a black sharpie to color the edges of the white foam adhesive square so it’s not so noticeable:) Use foam adhesive squares to attach the front paws to the top section of the basket and the back feet and tail to the bottom section.
6. Flip the combined basket over. Fold the basket base at the score lines.
7. Apply glue to the top two tabs on the basket base and secure to the rounded shape above.
8. Apply glue to the bottom two tabs on the basket base and secure to the head shape above creating a box.
9. Insert the handle on either side of the basket.
10. Use three small lengths of thread and apply hot glue to one of the groups of ends. Attach underneath the nose. Repeat for the other side:)
11. I used enamel dots to accentuate the eyes and added a ribbon:)