Graduation Picture Frame 4X6 2018

Graduation Picture Frame 4X6 2018-JMRush

Frame Dimensions: W 4.5 x H 6.5”

The Graduation Picture Frame 2018 is self standing and can be used horizontally or vertically. This design is compatible with both 8X12 and 12X12 mats and folds flat for mailing.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut design pieces. ( I used double sided card stock) Be careful when removing the grad hat piece with the year cut out. It is delicate.
2. Glue the smaller mat to the top of the larger mat. Attach the grad hat with the year cut out to the solid grad hat piece ( I used foam adhesive squares for dimension:)
3. Apply glue to the back of the combined mat piece just along the very top. Secure to the front of the frame base. (Make sure the the score lines are at the bottom of the frame base)
4. Use foam adhesive squares to attach the combined grad hat to the center of the top of the combined frame pieces. ( This frame can also be used horizontally by glue the mat along the horizontal top instead of the vertical as directed above)
5. Insert picture by lifting the mat. The score lines on the frame base can be used to utilize the kick stand:)

Leaf 3D 4x6 Photo Frame

Leaf 3D 4x6 Photo Frame - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

Fits 4X6 photos.

This easy to construct, two piece frame can be used vertically or horizontally and features a fold out stand and a decorative leaves. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the SVG and Cricut file here:

http://digiplayground.com/Jennifer-Rush/

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut out design piece. ( I used double sided card stock)

2. Insert the tabs of the frame base into the frame base slots.

3. Image of step 2 completed.

4.-5. Align and center the pieces. On the backside. Apply glue to the inside of the tabs and secure into place.

6. Pre-fold all scored lines on the edges of the frame folding them inward toward the center. Fold all score lines on the flower pieces. For each set of the flowers- fold one in and one out.

7. Starting on the right side of the frame base, apply hot glue to the very edge. 

8.  Place the glued edge down so the it is in alignment with the bottom score line. This will form a box.

9. Roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure.

10.-15. Repeat this steps for each of the frame sides. Be careful to only apply glue to the edge of each side so that the stand leg on the base of the frame will have mobility later and so inserting your photo is easy:)

16.-18. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure. Repeat for each tab.

19. Match up the leaves and glue the smaller leaves to the larger ones.

20. Curve your combined leaves as you like.

21. Insert your photo by sliding it into place. The sides of the frame will lift up a bit to ease the photo insertion.

22.-23. Glue the largest combined leaves in the corners of the frame. Note: This frame can be used horizontal ( as shown) or vertical. Use foam adhesive squares to attach the middle sized leaves. I used a dab of glue on the stem to secure the bottom of the middle sized leaves. Glue the smallest combined leaves to the frame:)

3D Spider Web Photo Frame 4X6

3D Spider Web Photo Frame 4X6 - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

Fits 4X6 photos

This easy to construct, two piece frame can be used vertically or horizontally and features a fold out stand, a decorative webbed mat, and a spider. This design is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut out design piece. (I used double sided card stock)

2. Insert the tabs of the frame base into the frame base slots (as shown in the image)

3.  Align and center the pieces. On the backside. Apply glue to the inside of the tabs and secure into place making sure that the corners are 90 degree angles.

4. Apply glue to the top backside and lower left of the solid rectangle shape that was the inside of your webbed mat piece. ( The image shows glue to the frame base to demonstrate the area where glue should not be present) Center and glue to the inside rectangle of the frame base making sure that the score lines for the frame stand remain moveable.

5. Pre-fold all scored lines on the edges of the frame folding them inward toward the center. Fold all score lines on the tabs inward.

6.  Starting on the side of the frame base, apply hot glue to the very inside score line on that side of the frame base.

7.  Place the edge down so the it is in alignment with the bottom score line. This will form a box.

8.-9. Depending on how quickly you work, you can roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure. ( image 8 shows applying more hot glue before you roll the box inward if your glue has dried)

10. Repeat this steps for each of the frame sides. (You will need to be careful a little more careful on the left side when applying glue to the score line so that the stand leg of the frame will have mobility later.)

11.-13. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure.

14. Repeat for each tab.

15 .Insert your photo by sliding it into place. The sides of the frame will lift up a bit to ease the photo insertion. On the backside, you can raise the stand flaps so that your frame sits vertically…..

16. Or you can raise the stand flap so that your frame sits horizontally.

17. -18. Using a ruler, line the edge of the ruler along the score line and fold upward on each side of the webbed mat.

19. Pinch the corners and fold at the angled score line on the web window. The last three steps are to create a 3D frame-like web window.

20. Apply glue to the backside of the web window just along the very inside edges.

21. Center and secure to the matching inside rectangle shape of the frame body.

22. Shape/Curve your spider. I used large enamel dot to accentuate the hind end. 

23. I used a black marker to color the sides of the white foam adhesive square that I used to secure the spider to the combined frame so that the edges didn’t show.

24. Ta Da:)

Graduation Picture Frame 4X6 2016

Graduation Picture Frame 4X6 2016-JMRush

Frame Dimensions: W 4.5 x H 6.5”

The Graduation Picture Frame 2016 is self standing and can be used horizontally or vertically. This design is compatible with both 8X12 and 12X12 mats and folds flat for mailing. 

1. Cut design pieces. ( I used double sided card stock)
2. Glue the smaller mat to the top pf the larger mat. Glue the grad hat with the year cut out to the solid grad hat piece.
3. Apply glue to the back of the combined mat piece just along the very top. Secure to the front of the frame base. (Make sure the the score lines are at the bottom of the frame base)
4. Use a foam adhesive square to attach the combined grad hat to the center of the top of the combined frame pieces. ( This frame can also be used horizontally by glue the mat along the horizontal top instead of the vertical as directed above)
5. Insert picture by lifting the mat.
6. The score lines on the frame base can be used to utilize the kick stand:)

3D Heart 4x6 Photo Frame

3D Heart 4x6 Photo Frame - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

This easy to construct, two piece frame can be used vertically or horizontally and features a fold out stand, decorative heart cut outs, and two 3-D hearts. This design is compatible with both 8X12 and 12X12 mats. The 3-D hearts can also be used separately. 

1.Cut out the design pieces. ( there is a rectangle shape absent from this image that is inserted at the end of the tutorial:)

2.- 5. Fold the score lines on the hearts. Apply glue to the backside of one half of one of the hearts and join it to the back half of another. Repeat this step until all 5 of this size heart is joined.

6. Repeat for the smaller sized hearts. Flip the frame base over.

7. Pre-fold all the score lines on the edges of the frame base folding them inward toward the center.

8. Insert the tabs of the frame base into the frame base slots on the other frame base piece.

9. Align and center the two pieces. 

10. -12. Glue the the inside tabs and secure into place. On the backside, apply glue to the the inside of the tab and secure to the other frame base.

13. Starting on the top edge of the frame base, apply hot glue to the very edge.

14. Place the glued edge down so that it is in alignment with the bottom score line. This is form a box.

15. Roll the box inward toward the center of the frame. This action will apply glue to the base of the frame. Hold until the glue is secure. Repeat this step for each side. (Be careful to only apply glue to the edge of each side so that the stand on the base of the frame will have mobility later and so your photo will insert easy)

16.-18. Fold the score lines on each side of each tuck tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure. Repeat for each tab.

19. -21.Apply glue to the inside of the frame careful not to glue the stand section ( the section with the score lines). You can pre-fold the stand out at this point. Place the rectangle piece inside, center, and secure into place. The edges of the frame will flex upward to allow this piece ( and your photo later) to fit inside.

22. Using foam adhesive squares, attach the combined heart to the frame.

23. I finished the frame with ribbon and an enamel dot on the ribbon:)

Poinsettia 3D 4x6 Photo Frame

Poinsettia 3D 4x6 Photo Frame - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

This easy to construct, two piece frame can be used vertically or horizontally and features a fold out stand and a decorative poinsettia. This design is compatible with both 8X12 and 12X12 mats. Poinsettia flower and leaves can also be used separately.

You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222

1. Cut out design piece.

2. Insert the tabs of the frame base into the frame base slots.

3. 4. Align and center the pieces. On the backside. Apply glue to the inside of the tabs and secure into place.

5. Pre-fold all scored lines on the edges of the frame folding them inward toward the center. Fold all score lines on the flower pieces. For each set of the flowers- fold one in and one out.

6. Line up the points of the Largest flower set. Make sure you have one flower fold down and one up. Glue the center to secure it together.

7. Apply glue to the flower edges.

8. Secure the point pieces together working your way around the flower until all points are glued together. Repeat for the other two flower sets.

9. Attach a foam adhesive square to the center of the two largest flowers.

10. Attache the flower sections together staggering the points. Largest on bottom ascending to the smallest. Shape the petals of the flower as you like.

11. I used 4 small adhesive jewels in the center of the poinsettia . Curve the leaves as you like.

12.  Starting on the top edge of the frame base, apply hot glue to the very edge. 

13.  Place the glued edge down so the it is in alignment with the bottom score line. This will form a box.

14. Roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure.

15.-21. Repeat this steps for each of the frame sides. Be careful to only apply glue to the edge of each side so that the stand leg on the base of the frame will have mobility later and so  inserting your photo is easy:)

22. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure.

23. Repeat for each tab.

24.Insert your photo by sliding it into place. The sides of the frame will lift up a bit to ease the photo insertion.

25. Use foam adhesive squares to attach the poinsettia and leaves onto your 3D frame:)

Christmas Lightbulb Window Picture Frame

Christmas Lightbulb Window Picture Frame - JMRush  Frame Dimensions: W5” x H 6.25”

This Christmas themed frame features a fold out stand and is sized for four “exchange” or “mini” sized (1.75 x 2.5”) pictures. Black thread is needed for the wire look of this design. 

1. Cut design pieces.
2. Separate the kickstand.
3. Apply glue to the front of the kickstand piece. Center and attach the solid frame piece making sure that the kickstand does not get glued down.
4. Apply glue down the center line going across the backside of the window piece. Apply glue to the very center line going up and down the backside of the window piece. ( Your glue should be in a cross shape). Make sure that the edges on the left and right do not get glued down so that you can insert photos:). Glue the very top and very bottom of the backside horizontally. Center and secure to the front of the combined frame pieces.
5. You can insert photos on either side:)
6. Using foam adhesive squares, center and attach the window box piece to the front bottom of the frame. Using foam squares again, attach the window box trim piece.
7. Glue the lightbulbs to their solid bases.
8. Glue the small plug in detail to the lightbulbs.
9. Layout the lightbulbs as you like.
10. Using black sewing thread, weave around the lightbulbs as you glue them into place. ( I changed the color of the frame..sorry. The beige frame was just not working for me;)

Zombie Hear, See, Speak No Evil Stand Ups

Zombie Hear, See, Speak No Evil Stand Ups-JMRush

Stand Up size - each: W 6.5” X  H 6.5”

These Halloween styled Zombie Hear no evil, See no evil, and Speak no evil stand up decorations feature an optional kick stand so they can be displayed flat or standing. This file contains all three Zombie image set pieces and three intricate cut spider web design frames. This design is compatible with 8x12 or 12X12 mats. 

Lattice 3D 4X6 Frame

Lattice 3D 4x6 Frame - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

This frame has a intricate cut design along the border and can be used vertically or horizontally. This frame features a fold out stand so everything you need to display your pictures comes complete in this file (excluding your pictures;) This design requires a 12X12 cutting mat.

1. Cut out design piece.
2. Pre-fold all scored lines on the outside of the frame folding them inward toward the center. (See 4 X 6 Frame picture tutorial above for more detailed pictures:)
3. Starting on the bottom edge ( the edge under the stand up leg score lines) apply hot glue to the edge. Be careful to only apply it to the edge so that the stand leg on the base of the frame will have mobility later and so that inserting your photo is easy:)
4. Place the glued edge down so the it is in alignment with the bottom score line. This will form a box.
5. Roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure.
6. Repeat this steps for each of the frame sides.
7. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure.
8. Repeat for each tab.

Pumpkin 3D 4X6 Frame

Pumpkin 3D 4x6 Frame - JMRush 

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8”

This Autumn themed frame has a intricate cut Pumpkin/leaf design along the border and can be used vertically or horizontally. This frame features a fold out stand so everything you need to display your pictures comes complete in this file (excluding your pictures;) This design requires a 12X12 cutting mat and contains a print and cut feature for the pumpkin and leaves. The pumpkin and leaves can also be used separately.

1. Cut out all design pieces.
2. Pre-fold all scored lines on the outside of the frame folding them inward toward the center. (See 4 X 6 Frame picture tutorial above for more detailed pictures:)
3. Starting on the bottom edge ( the edge under the stand up leg score lines) apply hot glue to the edge. Be careful to only apply it to the edge so that the stand leg on the base of the frame will have mobility later and so that inserting your photo is easy:)
4. Place the glued edge down so the it is in alignment with the bottom score line. This will form a box.
5. Roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure.
6. Repeat this steps for each of the frame sides.
7. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure.
8. Repeat for each tab.
9. Place the print and cut Pumpkins and leaves on top of the base frame and glue into place.
10. (I used foam adhesive squares to adhere them into place on the frame to give them dimension. Happy Crafting:)

Sketch Toy Picture Frame

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8"

1. Cut out all design pieces.
2. Pre-fold all scored lines on the outside of the frame folding them inward toward the center. (See 4 X 6 Frame picture tutorial above for more detailed pictures:)
3. Starting on the bottom edge ( the edge under the stand up leg score lines) apply hot glue to the edge. Be careful to only apply it to the edge so that the stand leg on the base of the frame will have mobility later:)
4. Place the glued edge down so the it is in alignment with the bottom score line. This will form a box.
5. Roll the box inward toward the center of the frame. This action will apply the glue edge to the base of the frame. Hold until the glue is secure.
6. Repeat this steps for each of the frame sides.
7. Fold in the score lines on each side of each tab. Apply a dab of hot glue. Fold the tab into the tab hole and hold until the glue is secure.
8. Repeat for each tab.
9. Insert your picture.
10. Place the Sketch frame on top of the base frame and glue into place.
11. Glue the knobs together and using foam adhesive squares adhere them into place on the frame. Happy Crafting:)

Finished Frame Dimensions: W 7 1/8"X H 5 1/4" X D 5/8"
This design requires a 12X12 mat.