Graduation Picture Frame 4X6 2018

Graduation Picture Frame 4X6 2018-JMRush

Frame Dimensions: W 4.5 x H 6.5”

The Graduation Picture Frame 2018 is self standing and can be used horizontally or vertically. This design is compatible with both 8X12 and 12X12 mats and folds flat for mailing.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222

1. Cut design pieces. ( I used double sided card stock) Be careful when removing the grad hat piece with the year cut out. It is delicate.
2. Glue the smaller mat to the top of the larger mat. Attach the grad hat with the year cut out to the solid grad hat piece ( I used foam adhesive squares for dimension:)
3. Apply glue to the back of the combined mat piece just along the very top. Secure to the front of the frame base. (Make sure the the score lines are at the bottom of the frame base)
4. Use foam adhesive squares to attach the combined grad hat to the center of the top of the combined frame pieces. ( This frame can also be used horizontally by glue the mat along the horizontal top instead of the vertical as directed above)
5. Insert picture by lifting the mat. The score lines on the frame base can be used to utilize the kick stand:)

Graduation Hat Pocket Gift Card

Graduation Hat Pocket Gift Card-JMRush

Approximate Size: W 7.25” X H 3.75”

This design has a sliding compartment that is sized to hold American paper currency or most gift cards and is compatible with both 8X12 and 12X12 mats.

You can purchase the Silhouette design file here: https://www.silhouettedesignstore.com/artists/485222 

1. Cut design pieces. I used double sided card stock.
2. Fold the score lines on the two card bases.  (There is a enlarged photo below to assist in folding the card bases. Green lines fold down. Red folds up. The lower card base if turned so that the point is pointing up instead of down.) Glue the thinner word to the thicker word base. Glue the small oval to the larger oval base. Glue the smaller hat pieces to their larger coordinating shapes. ( There is a small tab in the center of the smaller top hat piece that can be used to secure a real tassel or thread if you prefer. Make sure this tab is up and not glued down if you decide to not use the tassel piece provided) Glue the side banner pieces (2) to the coordinating shape on the full banner. Glue the smaller curved banner piece to it’s coordinating larger shape.
3. Apply glue to the side tabs on the lower card base and fold the bottom section to them.
4. Apply glue to the side tabs on the upper card base and secure to the upper rectangular panel.
5. This is what it should look like.
6. Push down on the top of the upper card base and crease the folds.
7. Apply glue to the top section of the upper card base and secure the combined top hat piece to it; aligning at the top of the card.
8. Glue the bottom combined hat piece to the lower card base at the coordinating “v” shape. Glue the combined word to the combined curved banner piece.

9.  Use foam adhesive on the center backside of the combined curved banner and secure to the coordinating shape on the combined full banner piece. (You can glue the side edges down to the combined full banner if you want a more rounded appearance). Using a thin round dowel, wrap the tassel piece around to the backside.

10.   Apply glue to the very top to secure the tassel piece

11.  Apply glue to the center of the combined top hat. Secure the oval shape of the tassel to it. ( You can attach a real tassel to the tab if not using the tassel provided)

12.  Glue the combined small oval piece on top of the oval shape of the tassel.

13.  This is what it should look like:)

14.  Apply glue to the lower section on either side ( where my fingers are pointing) and attach to the lower section.

15.  Insert a gift card or money. The top section will flex.

16.  Insert the upper combined card base into the lower combined card base.

17.  Glue the combined banner to the front of the lower combined card base.

Martini Cheers Card

Martini Cheers Card-JMRush

Approximate Card size: H 5.50” X W 4.25”

This design is compatible with both 8X12 and 12X12 mats.
You can purchase this design here: https://www.silhouettedesignstore.com/artists/485222

1.Cut design pieces.

2. Fold the card base. Glue the smaller martini glass to the larger one. Glue the Cheers word to it’s solid base. Glue the smaller triangular piece to the larger one aligning at the bottom.

3. Glue the combined triangular pieces to the combined martini glass- aligning at the top and center. Glue the small circle to the coordinating shape on the combined martini glass.

4. Glue the combined martini glass to the front of the card base. Glue the cheers word to the inside edge:)

Graduation Confetti

Graduation Confetti-JMRush

This graduation confetti is a fun way to decorate for your new graduate. 

Cheers! Gift Card Holder

Cheers! Gift Card Holder-JMRush

Approximate Card size: 3.5” x 5” 

This card features an optional gift card holder and fits a standard A2 size envelope. This design is compatible with both 8X12 and 12X12 mats. 

1.Cut design pieces. (I used double sided cardstock for the card base). (There is an optional gift card holder which design changes during the tutorial.)

2. Fold the card along score lines. Center and glue the Cheers beer image to it’s solid matching base. Using foam adhesive squares, attach the smaller foam to the larger one.

3. Apply glue the bottom of the optional gift card holder. (Make sure that you do not glue the inside flaps).

4. Center it to the inside of the card base and secure into place.

5. Insert Gift Card.

6. Glue the Combined cheers beer designs to it’s handled base. Glue this combination to the card base. Glue the foam design on top:)